It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
Being by obtaining the right tools. These will include getting a shovel, a post hole digger, a driving tool, and a hammer or mallet. The rod itself is about eight feet long and made of copper. Make sure to check that it is for grounding electricity or it may not provide the protection that you need. Without the right type, you could be in danger of a house fire.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
Once the hole is deep enough to start, add water. This will help soften the soil and make the rest of the job a bit easier. Place the rod in the hole and start pushing it around. One end should be pointed and this is the end that goes into the ground first. As you push it, you may add more water to help soften the dirt even more. Eventually, you will need to use a mallet, hammer or driver to complete the job of putting the rod all the way into the ground.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
Being by obtaining the right tools. These will include getting a shovel, a post hole digger, a driving tool, and a hammer or mallet. The rod itself is about eight feet long and made of copper. Make sure to check that it is for grounding electricity or it may not provide the protection that you need. Without the right type, you could be in danger of a house fire.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
Next, start digging. If you have the post hole digger, you can use it to get a few feet down. These are better than shovels because you do not need a wide hole, but a deep one. If you only have a shovel it will do, but the hole won't be as deep. Either way, you will get a good start and be on your way.
Once the hole is deep enough to start, add water. This will help soften the soil and make the rest of the job a bit easier. Place the rod in the hole and start pushing it around. One end should be pointed and this is the end that goes into the ground first. As you push it, you may add more water to help soften the dirt even more. Eventually, you will need to use a mallet, hammer or driver to complete the job of putting the rod all the way into the ground.
Once it is a few feet in the ground, grab the other tools to get it to go the rest of the way. The best is a pile driver. This is designed to fit over the pole and allow you to push it in with less effort by lifting and slamming it back down onto the pole. If you do not have one, you might use a two by four to make the surface easier to hit with a hammer or rubber mallet. Hammer the pole until it is either a couple of inches above or level with the hole.
At this point, you will need to attach the ground wire. Some might want to solder it, but the best option is to have a copper clamp designed for this job. The end of the ground wire should be exposed. Make sure to give it some slack so if the wire is hit or bumped it won't pop loose from the clamp.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
Không có nhận xét nào:
Đăng nhận xét