Certain reasons may drive you to repair your television. This includes your device powering itself off or taking a long time to get reception when you turn it on. The good thing is that such problems can be resolved by repairing the TV power supply. The process is not very hard when you have proper guidelines.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Locate the faulty capacitors. They are cylinder-shaped and vary in width and height. Most of them appear normal and therefore look for ones with a brown-yellow liquid coming from the top, or it has bulged at the top. This is an indication that the capacitors have overheated and are the cause of the fault. Remove them ensuring that you do not damage copper pads.
After all of the bad ones have been gotten rid of, replacement with new ones ought to be done. Make sure you note the positive and negative polarity while doing the replacement. Mark negative leads using a soldering iron on the board. The negative side normally has a stripe colored in gray. The capacitors need to be correctly installed since they are polarity complex.
Reassemble the device and the check power. After replacing connectors, back panel and screws, confirm whether the issue has been resolved. A power surge probably may have caused the fuse to blow. If the problem is not yet resolved, test the fuse. You will have to look for the appropriate fuse and replace it with the old one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
There are a number of tools you will need to effectively do the job. They include a capacitor, soldering iron, solder, screwdriver and a solder sucker. Confirm that your toolbox has all these items, and if not, you will have to go to the store. You should first determine if the problem is really what you want to repair. In television electric supplies, capacitors normally go bad causing them to leak and bulge hence the monitor will not get power.
Once the television has been unplugged from its power source, ensure you place it on a flat area with the screen facing down to prevent any damages. You can then detach all screws that have attached the back panel with a screwdriver. After all of them have been removed, you can detach the back panel by wiggling it a little bit since it is not secured with bolts and then keep it aside.
The next step is to locate where the circuit board is by following the board that the power cord is linked to. Disconnect the screws and connectors by using a screwdriver from the board. Ensure you note where they all came from as you will have to reattach them as they were. It is imperative you take pictures so that you do not get confused during reattaching. After the connectors and screws are unattached, remove the circuit board.
Locate the faulty capacitors. They are cylinder-shaped and vary in width and height. Most of them appear normal and therefore look for ones with a brown-yellow liquid coming from the top, or it has bulged at the top. This is an indication that the capacitors have overheated and are the cause of the fault. Remove them ensuring that you do not damage copper pads.
After all of the bad ones have been gotten rid of, replacement with new ones ought to be done. Make sure you note the positive and negative polarity while doing the replacement. Mark negative leads using a soldering iron on the board. The negative side normally has a stripe colored in gray. The capacitors need to be correctly installed since they are polarity complex.
Reassemble the device and the check power. After replacing connectors, back panel and screws, confirm whether the issue has been resolved. A power surge probably may have caused the fuse to blow. If the problem is not yet resolved, test the fuse. You will have to look for the appropriate fuse and replace it with the old one.
If none of these solves the problem, your last option is to replace the main circuit board of the device. This is because if it is damaged, the television would not work correctly. Before doing this, you should have guidance on how it should be replaced so that you do not cause further damage to the device.
About the Author:
To help you get your TV power supply, simply go to our online page for details. You will find all the relevant information by clicking here http://www.tekbyus.com.
Không có nhận xét nào:
Đăng nhận xét